Frequently Asked Questions

If patients experience any difficulty removing the sensor from their skin, these products and techniques may help:  

General Removal Techniques 

• Loosen edge of adhesive with fingernail and use products listed below if necessary.^1,2  

• While removing tapes, use fingers of opposite hand to push skin down and away from adhesive. Continue to move fingers on skin towards adhesive as it is removed.²  

• ‘‘Fold back’’ technique: Remove adhesive slowly, at low angle, folding back on itself. ²  

• ‘‘Stretch and relax’’ technique: Films that stretch (e.g., IV3000 or Tegaderm) may be stretched horizontally away from the centre (opposite of the fold back technique) while walking fingers under the dressing to continue stretching it. ²  

• Use adhesive removal wipes to rub the skin under the tape towards the adhesive as it is removed. This helps loosen adhesive from skin and may help reduce pain with removal.¹  

For detailed step-by-step instructions on how to use the Dexcom G6 Continuous Glucose Monitoring (CGM) System, please refer to the User Guide. 

View the downloadable "Sensor Adhesion Best Practices" document, which outlines the step-by-step process for how to insert and remove a Dexcom G6 sensor patch. 

Yes, Dexcom G6 is indicated for children as young as 2 years old. 

Dexcom Sensors are manufactured with a special adhesive to help them stick to patients’ skin after insertion. Adhesive supplements may also be used.  

• Liquid adhesive agents can be used with the sensor adhesive patch.^1,3 Suggestions for patients when using liquid adhesive agents are to:  

1. Create an empty oval on the skin with the liquid adhesive product.  

2. Let skin adhesive dry.  

3. Insert sensor on clean skin in centre of oval.  

• Additional adhesive patches or tape can be applied over the sensor adhesive patch. ^1,2 Suggestions for patients when using adhesive patches or tapes are to:  

• Cut a hole in the adhesive patch or tape to fit around transmitter.  

• Cut the adhesive patch or tape into strips to use ‘‘picture frame’’ technique around sensor adhesive patch.^1,4  

For detailed step-by-step instructions on how to use the Dexcom G6 Continuous Glucose Monitoring (CGM) System, please refer to the User Guide.  Dexcom does not recommend, endorse or warrant any third-party products, including adhesive supplements and removal products. 

View the downloadable "Sensor Adhesion Best Practices" document, which outlines the step-by-step process for how to insert and remove a Dexcom G6 sensor patch. 

Register your clinic at https://clarity.dexcom.eu/professional/registration. Whoever completes the registration will be considered the account administrator with full ability to add and manage staff accounts.

Users might need administrator privileges to install software on their computers.  

A broadband network connection of 1.5 Mbps or more is required to install the software from the web, upload data or view the online User Guide.  

It is recommended that you use an appropriate firewall programme and an anti-virus programme on your computer to protect against viruses, malware and unauthorised access to and use of your computer and the information stored, processed and transmitted by it.  

Dexcom CLARITY supports the following system configurations:  

Windows 7, 8 or 10 

• 1.3 gigahertz (GHz) processor and 1 gigabyte (GB) free RAM with 100 megabytes (MB) free disk space 

• Microsoft .NET Framework 4.6.1 or greater, full version 

• Display resolution of 1024 x 768 pixels or greater 

• Chrome 53, Firefox 47, Internet Explorer 11 run in desktop mode or Microsoft Edge 

• USB 2.0+ port to connect the USB cable to upload a Dexcom receiver 

Mac OSX 10.10, 10.11, 10.12 or 10.13 

• 2.3 gigahertz (GHz) processor and 4 gigabytes (GB) free RAM with 100 megabytes (MB) free disk space 

• Display resolution of 1280 x 800 pixels or greater  

• Safari 9.1 or greater, Chrome 53 or Firefox 47 for Mac OSX 

• USB 2.0+ port to connect the USB cable to upload a Dexcom receiver 

Optional computer configurations:  

• Mouse or trackpad  

• A PDF reader (for example, Adobe Reader) for viewing, saving, and printing the reports  

• An Excel spreadsheet viewer (for example, Microsoft Excel or Excel Viewer)  

• Printer, for printed copies of reports  

To run Dexcom CLARITY, your network must allow the following outbound network traffic, which might require changes to proxy and network configuration:  

• dexcom.com (and all subdomains) on port 443  

• agent.mydiabetesdata.com with DNS loopback support to 127.0.0.1

If your clinic has a Dexcom CLARITY account, add the patient to your patient list, then click Share data to view, print, or email a share invitation. The patient enters the Sharing Code from the invitation either into their personal Dexcom CLARITY account or into their Dexcom CLARITY App. Once sharing is established, it continues until the patient or clinic decides to stop sharing and manually stops it within Dexcom CLARITY.  

If your clinic does not have a Dexcom CLARITY account, patients can provide a Share Code generated from the Dexcom CLARITY App for your clinic to enter at https://clarity.dexcom.eu/  or you can guest upload a Receiver from the same link.

You can save or print all reports from Dexcom CLARITY for up to 90 days of data. While viewing a patient’s interactive report, from the top of the page click Print Reports to print or Download Reports to save. Then, choose a date range and any or all of the reports.  

Yes. Dexcom CLARITY has the option to export data as a CSV file viewable in Excel. Export from one patient by clicking the Patient Name, then click Export. Or, export for all patients in your Patient List by clicking Export All Data from the top of your Patient List page.

• Overview – presents up to four clinically relevant patterns, dashboard statistics, as well as the patient’s Best Day. This quick summary can help focus the discussion on problem areas contributing to hyper- and hypoglycaemia.  

• Patterns – dive deeper into each of the four clinically relevant patterns. Each pattern provides graphs of the days that contribute to that pattern.  

• Data – Trends and Overlay graphs show aggregate data with filtering options. Daily graphs offer a detailed view of every glucose data point for each day selected.  

• Compare – side-by-side comparison of Trends, Overlay and Daily graphs to encourage progress and highlight challenges patients may face.  

• Statistics – provides focused insight for both daily and hourly glucose metrics. Advanced metrics can be selected for deeper analytics.  

• AGP – standardized Ambulatory Glucose Profile (AGP) report provides a big picture view of diabetes management.

Once a patient has been added to the Patient list, click the Patient Name to invite them to share their data or choose to upload Receiver data. Once sharing has been initiated or the Receiver is uploaded, click the Patient’s Name, then click Go to access interactive reports.

For every release, a notification banner is posted at the top of the Dexcom CLARITY page on the day of the release. Follow the banner’s link to read the release notes. If the Uploader software is updated, the notification banner posts 2 weeks before the release.

If you have questions about Dexcom CLARITY, please contact your local Technical Support team via our Product Support Request form.

If you have questions, please contact our team via our Product Support Request form.